
Diffusion Bonding in 3D-Manufacturing of Titanium Alloy Structures
Fig. 1: Optical images (“top view”) of the initial Ti-6Al-4V alloy parts.
Lees artikel →Mat-Tech is een pionier op het gebied van wereldwijde vooruitgang op het gebied van hightech solderen. Blijf voorop met onze geavanceerde oplossingen en expertise op het gebied van geavanceerde metaalverbindingen.
Mat-Tech is always at the forefront of global advancements in high-tech brazing Onze afdeling Development & Testing beschikt niet alleen over de nieuwste onderzoeken, maar speelt ook een actieve rol in diverse internationale initiatieven. Wij geloven in het verspreiden van de inzichten die we opdoen onder onze klanten, collega’s uit de sector en andere belanghebbenden met interesse in hightech hardsolderen. Ontdek hoe we onze expertise delen op beurzen, workshops en onder andere via dit platform.

Fig. 1: Optical images (“top view”) of the initial Ti-6Al-4V alloy parts.
Lees artikel →
ABSTRACTSuccessful brazing of any Aluminium alloy requires prior removal of the native surface oxide film,which is usually done by…
Lees artikel →
Aluminium Oxide Ceramics due primarily to its good heat conductivity (of about 30 W×m-1×K-1) and a relatively low cost is considered as an…
Lees artikel →
Although cemented carbide is resistance to thermal shock, it will not withstand stresses caused by severe thermal gradients when brazed to…
Lees artikel →
Brazing of several refractory metals, namely, Tungsten, Molybdenum and Niobium as wellas austenitic stainless steel AISI 304 to pure Copper…
Lees artikel →
Our previous investigation of the interfacial regions in the ”(p-n) thermocouple” / Cu- connector assembly (Project No. 2012-3067-0616) was…
Lees artikel →
The continued demand for reliable sources of energy can be addressed by the discovery of new sustainable energy sources as well as…
Lees artikel →
The present Project is dealing with the fabrication of electrical (high-voltage) feedthrough consisting of YSZ (ZrO2 + 3 % mole Y2O3) body…
Lees artikel →
Composition (in weight %) of the low-carbon, low-alloy P265GH-(“killed”) steel is C0.2; Si0.4; Mn 0.8-1.4; P0.025; S0.015; N0.012; Cu0.3;…
Lees artikel →
Aluminium Oxide Ceramics is considered as an attractive material in designing of various components when “thermal management issues” are of…
Lees artikel →
Brazing and Diffusion Bonding TZM to Graphite Using Cu, Ti, Pd and Cr Filler Metals
Lees artikel →
One can braze the higher Mg-content heat-treatable AA-6082 series Al alloys, (containing Mg, Si, Fe, Mn, Cr, Zn, Ti), with a near-eutectic…
Lees artikel →
This combination of technologies is essential in designing various plate and shell-type heat-exchangers. Application is shown in the…
Lees artikel →
Thermo-mechanical stresses that built up from cool-down after soldering will affect the overall longevity performance of such devices. To…
Lees artikel →
Certain Aluminium alloys can be successfully soldered using low melting solders. Read here how we do it.
Lees artikel →
The stand-off of a flip-chip is governed by the equilibrium between the weight of the chip and the counteracting spring formed by the…
Lees artikel →
The shape of a liquid drop is governed by what is known as the Young-LaPlace equation. It was derived more or less simultaneously by Thomas…
Lees artikel →
Transient Liquid Phase Bonding is applied well below the aging temperature (450-480˚C) of the CuCrZr-alloy, whereas the resulting joints…
Lees artikel →
Ultra-low melting leadfree solder compositions can be used for stress reduction in joints in a bio-ambient or temperature sensitive…
Lees artikel →
The relation between surface tension and contact angles as a measure for the wetting capability is due to Thomas Young (1804). A short…
Lees artikel →
For tracking of assets, low-cost interconnect technologies are required. This can be achieved through a low melting lead-free matrix with…
Lees artikel →
In case one assumes that the bump is built from shearing discs, a simple model of a deflected bump can be made.
Lees artikel →
The material of CLIC accelerating structure disks is high conductivity Oxygen-free-electronic Cu. Fabrication of the CLIC disk stack occurs…
Lees artikel →
Soldering with low-temperature Pb-free alloys is a viable replacement for conductive adhesives in back-contacted solar panels.
Lees artikel →
In 1819 Pierre Louis Dulong and Alexis Thérèse Petit found that the specific molar heat for metals is approximately 3 R @ 25 J/K. Here R is…
Lees artikel →Laten we praten